ATA6660-TAQY 19

Features • • • • • • • • • • Usable for Automotive 12 V/24 V and Industrial Applications Maximum High-speed Data Transmissions up to 1 MBaud Fully Compatible with ISO 11898 Controlled Slew Rate Standby Mode TXD Input Compatible to 3.3 V Short-circuit Protection Overtemperature Protection High Voltage Bus Lines Protection, -40 V to +40 V High Speed Differential Receiver Stage with a Wide Common Mode Range, -10 V to +10 V, for High Electromagnetic Immunity (EMI) • Fully Controlled Bus Lines, CANH and CANL to Minimize Electromagnetic Emissions (EME) • High ESD Protection at CANH, CANL HBM 8 kV, MM 300 V High-speed CAN Transceiver ATA6660 Description The ATA6660 is a monolithic circuit based on the Atmel’s Smart Power BCD60-III technology. It is especially designed for high speed CAN-Controller (CAN-C) differential mode data transmission between CAN-Controllers and the physical differential bus lines. Figure 1. Block Diagram 3 VCC 1 TXD TXD input stage Overtemperature and Short circuit protection Driver 7 CANH 8 RS Constant slope/ standby 4 RXD Receiver 6 CANL 5 VREF Reference Voltage 0.5*VCC 2 GND Rev. 4582B–BCD–03/03 1 Pin Configuration Figure 2. Pinning SO8 TXD GND VCC RXD 1 2 3 4 8 7 6 5 RS CANH CANL VREF Pin Description Pin Symbol 1 TXD Function Transmit data input 2 GND Ground 3 VCC Supply voltage 4 RXD Receive data output 5 VREF Reference voltage output 6 CANL Low level CAN voltage input/output 7 CANH High level CAN voltage input/output 8 RS Switch standby mode/normal mode Functional Description The ATA6660 is a monolithic circuit based on Atmel’s Smart Power BCD60-III technology. It is especially designed for high-speed differential mode data transmission in harsh environments like automotive and industrial applications. Baudrate can be adjusted up to 1 Mbaud. The ATA6660 is fully compatible to the ISO11898, the developed standard for high speed CAN-C (Controller Area Network) communication. Voltage Protection and ESD High voltage protection circuitry on both line pins, CANH (Pin 7) and CANL (Pin 6), allow bus line voltages in the range of -40 V to +40 V. ESD protection circuitry on line pins allow HBM = 8 kV, MM = 300 V. The implemented high voltage protection on bus line output/input pins (7/6) makes the ATA6660 suitable for 12 V automotive applications as well as 24 V automotive applications. Slope Control A fixed slope is adjusted to prevent unsymmetrical transients on bus lines causing EMC problems. Controlled bus lines, both CANH and CANL signal, will reduce radio frequency interference to a minimum. In well designed bus configurations the filter design costs can be reduced dramatically. Overcurrent Protection In the case of a line shorts, like CANH to GND, CANL to VCC, integrated short current limitation allows a maximum current of ICANH_SC or ICANL_SC. If junction temperature rises above 165°C an internal overtemperature protection circuitry shuts down both output stages, the receiver will stay activated. 2 ATA6660 4582B–BCD–03/03 ATA6660 Standby Mode The ATA6660 can be switched to standby mode by forcing the voltage VRS > 0.87 ´ VCC. In standby mode the supply current will reduce dramatically, supply current during standby mode is typical 600 µA (IVCC_stby). Transmitting data function will not be supported, but the oppertunity will remain to receive data. A high-speed comparator is listening for activities on the bus. A dominant bus signal will force the output RXD to a low level in typical tdRXDL = 400 ns. If the RS pin is not connected, causing through a broken connection to the controller, the ATA6660 will switch to standby mode automatically. High-speed Receiver In normal mode a fast receiver circuitry combined with a resistor network is able to detect differential bus line voltages Vrec_th > 0.9 V as dominant bit, differential bus line voltages Vrec_th < 0.5 V as recessive bit. The wide receiver common mode range, -10 V to +10 V, combined with a symmetrical differential receiver stage offers high immunity against electromagnetic interference. A typical hysteresis of 70 mV is implemented. Dominant differential bus voltages forces RXD output (Pin 4) to low level, recessive differential bus voltages to high level. TXD Input The input stage Pin 1 (TXD) is compatible for 3.3 V output levels from new controller families. Pull-up resistance (25 kW) forces the IC to recessive mode, if TXD-Pin is not connected. TXD low signal drives the transmitter into dominant state. Transmitter A integrated complex compensation technique allows stable data transmission up to 1 MBaud. Low level on TXD input forces bus line voltages CANH to 3.5 V, CANL to 1.5 V with a termination resistor of 60 W. In the case of a line short circuit, like CANH to GND, CANL to VCC, integrated short current limitation circuitry allows a maximum current of 150 mA. If junction temperature rises above typical 163 ° C an internal overtemperature protection shuts down both output stages, the receive mode will stay activated. Split Termination Concept With a modified bus termination (see Figure 5) a reduction of emission and a higher immunity of the bus system can be achieved. The one 120 W resistor at the bus line end nodes is split into two resistors of equal value, i.e., two resistors of 60 W. The resistors for the stub nodes is recommended with two resistors of 1,3 kW. (for example 8 stub nodes and 2 bus end nodes) Notice: The bus load of all the termination resistors has to stay within the range of 50 W to 65 W. The common mode signal at the centre tap of the termination is connected to ground via a capacitor of e.g., Csplit = 10 nF to 100 nF. A seperate ground lead to the ground pin of the module connector is recommended. 3 4582B–BCD–03/03 Absolute Maximum Ratings Parameters Symbol Min. Max. Unit VCC -0.3 +6 V VTXD, VREF, VRS, VRXD -0.3 VCC +0.3 V -40.0 +40.0 V Supply voltage DC voltage at Pins 1, 4, 5 and 8 DC voltage at Pins 6 and 7 Conditions VCANH, VCANL 0 V < VCC < 5.25 V; no time limit Transient voltage at Pins 6 and 7 -150 +100 V Storage temperature TStg -55 +150 °C Operating ambient temperature Tamb -40 +125 °C ESD classification All pins HBM ESD S.5.1 MM JEDEC A115A ±3000 ±200 V V ESD classification Pin 6, 7 versus Pin 2 HBM 1.5 kW, 100 pF MM 0W, 200 pF ±8000 ±300 V V Thermal Resistance Parameters Thermal resistance from junction to ambient Symbol Value Unit RthJA 160 K/W Truth Table VCC TXD RS CANH CANL Bus State RXD 4.75 V to 5.25 V 0 < 0.3 ´ VCC 3.5 V 1.5 V Dominant 0 4.75 V to 5.25 V 1 (or floating) < 0.3 ´ VCC 0.5 ´ VCC 0.5 ´ VCC Recessive 1 4.75 V to 5.25 V X > 0.87 ´ VCC 0.5 ´ VCC 0.5 ´ VCC Recessive 1 RS (Pin 8) Functionality Slope Control Mode Voltage and Current Levels VRS > 0.87 ´ VCC Standby IRS < | 10 µA | VRS < 0.3 ´ VCC Constant slope control IRS £ 500 µA 4 ATA6660 4582B–BCD–03/03 ATA6660 Electrical Characteristics VCC = 4.75 V to 5.25 V; Tamb = -40°C to +125°C; RBus = 60 Ω; unless otherwise specified All voltages referenced to ground (Pin 2); positive input current. No. 1 Parameters Test Conditions Pin Symbol Min. Typ. Max. Unit Type* Supply Current 1.1 Supply current dominant VTXD = 0 V VRS = 0 V 3 Ivcc_dom 45 60 mA A 1.2 Supply current recessive VTXD = 5 V VRS = 0 V 3 Ivcc_rec 10 15 mA A 1.3 Supply current standby VRS = 5 V 3 Ivcc_stby 600 980 µA A 2 Transmitter Data Input TXD 2.1 HIGH level input voltage VTXD = 5 V VRS = 0 V 1 VTXDH 2 VCC+0.3 V A 2.2 LOW level input voltage VTXD = 0 V VRS = 0 V 1 VTXDL -0.3 +1 V A 2.3 HIGH level input current VTXD = VCC 1 IIH -1 0 µA A 2.4 LOW level input voltage VTXD = 0 V 1 IIL -500 -50 µA A 3 Receiver Data Output RXD 3.1 High level output voltage IRXD = -100 µA 4 VRXDH 0.8 ´ VCC VCC V A 3.2 Low level output voltage IRXD = 1 mA 4 VRXDL 0 0.2 ´ VCC V A Short current at RXD VTXD = 5 V VRXD = 0 V 4 IRXDs1 -3 -1 mA A Short current at RXD VTXD = 0 V VRXD = 5 V 4 IRXDs2 2 6 mA A 3.3 3.4 4 Reference Output Voltage VREF 4.1 Reference output voltage normal mode VRS = 0 V; -50 µA < I5 < 50 µA 5 Vref_no 0.45 VCC - 0.55 VCC V A 4.2 Reference output voltage standby mode VRS = 5 V; -5µA < I5 < 5 µA 5 Vref_stby 0.4 ´ VCC - 0.6 VCC V A 2.5 3.0 V A +5 mA A 5 DC Bus Transmitter CANH; CANL Recessive bus voltage VTXD = VCC; no load 6, 7 VCANH; VCANL 2.0 IO(CANH)(reces) IO(CANL)(reces) -40 V < VCANH; VCANL < 40 V; 0 V < VCC < 5.25 V 6, 7 IO_reces -5 5.3 CANH output voltage dominant VTXD = 0 V 6, 7 VCANH 2.8 3.5 4.5 V A 5.4 CANL output voltage dominant VTXD = 0 V 6, 7 VCANL 0.5 1.5 2.0 V A 5.1 5.2 *) Type means: A = 100% tested, B = 100% correlation tested, C = Characterized on samples, D = Design parameter 5 4582B–BCD–03/03 Electrical Characteristics (Continued) VCC = 4.75 V to 5.25 V; Tamb = -40°C to +125°C; RBus = 60 Ω; unless otherwise specified All voltages referenced to ground (Pin 2); positive input current. No. Parameters Test Conditions Pin Symbol Min. Typ. Max. Unit Type* Differential bus output voltage (VCANH – VCANL) VTXD = 0 V; RL = 45 W to 60 W; VCC = 4.9 V 6, 7 Vdiffdom 1.5 2 3.0 V A 5.5 5.6 VTXD = VCC; no load 6, 7 Vdiffrec -500 +50 mV A 5.7 Short-circuit CANH current VCANH = -10 V TXD = 0 V 6, 7 ICANH_SC -35 -100 mA A 5.8 Short-circuit CANL current VCANL = 18 V TXD = 0 V 6, 7 ICANL_SC 50 - 150 mA A 6 DC Bus Receiver CANH; CANL Differential receiver threshold voltage normal mode -10 V < VCANH < +10 V -10 V < VCANL < +10 V 6, 7 Vrec_th 0.5 0.7 0.9 V A Differential receiver threshold voltage stand-by mode VRS = VCC 6, 7 Vrec_th_stby 0.5 0.7 0.9 V A 6.2 6.3 Differential input hysteresis 6, 7 Vdiff(hys) mV A CANH and CANL common mode input resistance 6, 7 Ri 5 15 25 kW A 6.4 6.5 Differential input resistance 6, 7 Rdiff 10 30 100 kW A 6, 7 Ri_m -3 +3 % A 6.6 Matching between CANH and CANL common mode input resistance 6.7 CANH, CANL input capacitance 6, 7 Ci 20 pF D 6.8 Differential input capacitance 6, 7 Cdiff 10 pF D 6, 7 ILI(CANH); ILI(CANL) 250 µA A 6.1 6.9 CANH, CANL input leakage input current 7 Thermal Shut-down VCC = 0 V VCANH = 3.5 V VCANL = 1.5 V 70 Shut-down junction temperature for CANH/CANL TJ(SD) 150 163 175 °C B 7.1 Switch on junction temperature for CANH/CANL TJ(SD) 140 154 165 °C B 7.2 7.3 Temperature hysteresis THys K B 10 *) Type means: A = 100% tested, B = 100% correlation tested, C = Characterized on samples, D = Design parameter 6 ATA6660 4582B–BCD–03/03 ATA6660 Electrical Characteristics (Continued) VCC = 4.75 V to 5.25 V; Tamb = -40°C to +125°C; RBus = 60 Ω; unless otherwise specified All voltages referenced to ground (Pin 2); positive input current. No. 8 Parameters Test Conditions VRS = 0 V 8.2 Delay TXD to bus inactive VRS = 0 V 8.3 Delay TXD to RXD, recessive to dominant VRS = 0 V 8.4 Delay TXD to RXD, dominant to recessive VRS = 0 V 8.5 Difference between Delay TXD to RXD dominant to Delay recessive tdiff = td_activ(TXD-RXD) - td_inactiv(TXD-RXD) 9 Symbol Min. Typ. Max. Unit Type* 120 180 ns A 50 100 ns A 200 420 ns A 180 460 ns A 80 ns A 450 ns A 2 µs A 0.3 ´ VCC V A Timing Characteristics Normal Mode , VRS ≤ 0.3 ´VCC (see Figure 3) Delay TXD to bus active 8.1 Pin td(TXDBUS_ON) td(TXDBUS_OFF) 6, 7 td_activ(TXDRXD) td_inactiv(TXDRXD) tdiff -280 4 tdRxDL - 6, 7 Twake_up Timing Characteristics Stand-by Mode VRS ≥ 0.87 ´ VCC 9.1 Bus dominant to RXD low in stand-by mode VRS = VCC 300 TXD = 0 V VRS from 0 V to VCC 9.2 Wake up time after stand-by mode (time delay between standby to normal mode and to bus dominant) 10.1 Standby/Normal Mode Selecteable via RS (Pin 8) 10.1 Input voltage for normal mode VRS = VCC 8 VRS - 10.2 Input current for normal mode VRS = 0 V 8 IRS -700 µA A 10.3 Input voltage for stand-by mode 8 Vstby 0.87 ´ VCC V A - *) Type means: A = 100% tested, B = 100% correlation tested, C = Characterized on samples, D = Design parameter 7 4582B–BCD–03/03 Figure 3. Timing Diagrams HIGH TXD LOW dominant CANH CANH CANL dominant CANL dominant (bus activ) 0.9V Vdiff 0.5V recessive (bus inactive) HIGH 0.7VCC RXD 0.3VCC LOW td (TXD_bus_on) td (TXD_bus_off) t d_activ(TXD_RXD) 8 t d_inactiv (TXD_RXD) ATA6660 4582B–BCD–03/03 ATA6660 Figure 4. Test Circuit for Timing Characteristics TXD GND RXD C=47µF C=100nF 8 2 7 ATA6660 VCC + 5V 1 3 6 4 5 RS CANH CANL RL=62 CL=100pF Vref C=15pF Figure 5. Bus Application with Split Termination Concept bus line end node RS 7 CANH 6 CANL 5 + 5V 2 GND 8 1 TXD CAN Controller Vref ATA6660 3 VCC 4 RXD CSPLIT =10nF RL=60 RL=60 bus line stub node RL=1,3k C=15pF C=47µF C=100nF RL=1,3k 7 CANH 6 CANL 5 4 C=100nF RS Vref ATA6660 RXD C=47µF 8 VCC 3 + 5V 2 GND 1 TXD CAN Controller C=15pF CSPLIT =10nF RL=60 RL=60 CSPLIT =10nF bus line end node 9 4582B–BCD–03/03 Ordering Information Extended Type Number Package ATA6660 Remarks SO8 – Package Information Package SO8 Dimensions in mm 5.2 4.8 5.00 4.85 3.7 1.4 0.25 0.10 0.4 1.27 6.15 5.85 3.81 8 0.2 3.8 5 technical drawings according to DIN specifications 1 10 4 ATA6660 4582B–BCD–03/03 Atmel Headquarters Atmel Operations Corporate Headquarters Memory 2325 Orchard Parkway San Jose, CA 95131 TEL 1(408) 441-0311 FAX 1(408) 487-2600 Europe Atmel Sarl Route des Arsenaux 41 Case Postale 80 CH-1705 Fribourg Switzerland TEL (41) 26-426-5555 FAX (41) 26-426-5500 Asia Room 1219 Chinachem Golden Plaza 77 Mody Road Tsimhatsui East Kowloon Hong Kong TEL (852) 2721-9778 FAX (852) 2722-1369 Japan 9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan TEL (81) 3-3523-3551 FAX (81) 3-3523-7581 2325 Orchard Parkway San Jose, CA 95131 TEL 1(408) 441-0311 FAX 1(408) 436-4314 Microcontrollers 2325 Orchard Parkway San Jose, CA 95131 TEL 1(408) 441-0311 FAX 1(408) 436-4314 La Chantrerie BP 70602 44306 Nantes Cedex 3, France TEL (33) 2-40-18-18-18 FAX (33) 2-40-18-19-60 ASIC/ASSP/Smart Cards Zone Industrielle 13106 Rousset Cedex, France TEL (33) 4-42-53-60-00 FAX (33) 4-42-53-60-01 RF/Automotive Theresienstrasse 2 Postfach 3535 74025 Heilbronn, Germany TEL (49) 71-31-67-0 FAX (49) 71-31-67-2340 1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 TEL 1(719) 576-3300 FAX 1(719) 540-1759 Biometrics/Imaging/Hi-Rel MPU/ High Speed Converters/RF Datacom Avenue de Rochepleine BP 123 38521 Saint-Egreve Cedex, France TEL (33) 4-76-58-30-00 FAX (33) 4-76-58-34-80 1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 TEL 1(719) 576-3300 FAX 1(719) 540-1759 Scottish Enterprise Technology Park Maxwell Building East Kilbride G75 0QR, Scotland TEL (44) 1355-803-000 FAX (44) 1355-242-743 e-mail literature@atmel.com Web Site http://www.atmel.com © Atmel Corporation 2003. Atmel Corporation makes no warranty for the use of its products, other than those expressly contained in the Company’s standard warranty which is detailed in Atmel’s Terms and Conditions located on the Company’s web site. The Company assumes no responsibility for any errors which may appear in this document, reserves the right to change devices or specifications detailed herein at any time without notice, and does not make any commitment to update the information contained herein. No licenses to patents or other intellectual property of Atmel are granted by the Company in connection with the sale of Atmel products, expressly or by implication. Atmel’s products are not authorized for use as critical components in life support devices or systems. Atmel ® is the registered trademark of Atmel. Other terms and product names may be the trademarks of others. Printed on recycled paper. 4582B–BCD–03/03 xM